Integra ST2 Manuale Utente

ST2 Smart TunerINSTRUCTION MANUALDual AM/FM Tuner

10RS-232INTERFACEIRLRAUDIO OUTPUT12VDC 1.5AINOUTNEWMARKET,NH U.S.A.ST2 Smart Tuner LINKKEYPAD PORTSTUNER 1TUNER2FM COAXLOOPANTENNAFM COAXLOOPANTENNASe

11ST2 SETUP AND CONNECTIONSCAi SERIES AND A-BUS CONNECTIONS1RL21RL234CA6.4iNEWMARKET, NH U.S.A.~110VAC ~220-240VAC~50-60Hz400WVOLTAGE 110V220-240VFUSE

12ST2 SETUP AND CONNECTIONSANTENNA CONNECTIONS Connecting an Indoor and Outdoor AntennaThe diagram above depicts a typical setup using the ST2 Tuner w

13ST2 SETUP AND CONNECTIONSANTENNA CONNECTIONSGrounding an Outdoor AntennaIf the tuner is used with an outdoor antenna, the antenna must be grounded a

14Front Panel OperationTurning the unit onTo turn the unit on, push the On/Off button up on thefront panel. Pushing the On/Off button down turns thetu

15ST2 OPERATIONST2-RC REMOTE CONTROLST2-RC Remote Control OperationTurning the unit onTo take the ST2 tuner out of standby mode, pushor any other butt

16ST2 OPERATIONST2-KP KEYPAD CONTROLSST2-KP Keypad OperationTurning the keypad on/offTo activate the ST2-KP, press . Press topower down the keypad d

17ST2 OPERATIONUNO-S2 KEYPAD CONTROLS WITH CAV6.6CAV6.6-UNO-S2 Keypad OperationNOTE: To control the ST2 Tuner through theUNO-S2 keypad, the tuner must

18ST2 OPERATIONUNO-S2 KEYPAD CONTROLS WITH CAV6.6104.1 MHz FMTUNER SELECTION - Select source numberassigned to TUNER 1 or TUNER 2TUNE UP/DOWN - Used f

19UNO-LRC1 Remote Control OperationTurning the unit onThe tuner is power managed by the CAV6.6 or otherRNET-enabled controller. If the tuner is in sta

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

20ST2 OPERATIONUNO-LRC1 REMOTE CONTROL WITH CAV6.6POWER - Power managed by CAV6.6NUMERIC INPUT - Number buttons for directinput of frequency, preset,

21ST2 Tuner Setup MenusNote: The Setup Menu procedures must be performed from the ST2 Tuner front panel. The ST2 Tuner Setup Menus provide setup and n

22ST2 TUNER PROGRAMMINGST2 TUNER SETUP MENUPress and HoldTNR SEL buttonST2 Chassis Setup ProceduresTNRSELTNRSELThis Procedurereturns the ST2 Tunerto i

23System Info (Chassis)The System Info menu shows the ST2 Tuner’smanufacturing build properties.1. Enter the Setup Menu by pressing and holdingthe TNR

24ST2 TUNER PROGRAMMINGST2 TUNER SETUP MENUBank Name (AM/FM) (cont’d)14. Press BAND to save bank name. The BankName menu returns to the Tuner # prompt

25ST2 TUNER PROGRAMMINGPROGRAMMING FOR CAV6.6 USENOTE: The CAV6.6 firmware must be version 2.00.01 or higher and UNO-S2firmwaremust be version 3.00.01

26ST2 Smart TunerDimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm)Weight: 7 lbs. (3.2kg)Power Supply: 12VDC 1.5AFrequency Range: AM

27WARRANTY & REPAIRThe Russound ST2 Tuner is fully guaranteed against all defects in materials and workmanship for two(2) years from the date of p

Russound5 Forbes Road, Newmarket, NH 03857tel 603.659.5170 • fax 603.659.5388e-mail: [email protected] www.russound.comE. & O.E.Copyright © 2004

TABLE OF CONTENTSProduct Introduction...4-5Comp

4INTRODUCTIONDESCRIPTIONThank you for choosing the Russound ST2 SmartTuner. Whether you are adding radio to an exist-ing system, expanding a CAi Serie

5INTRODUCTIONIR-controlled SystemCAi Series -The ST2 Tuner can be controlled by infraredcommands received through the two IR connec-tions on the rear

6COMPONENT GUIDEST2 FRONT PANEL MAIN POWER SWITCH - Turns power on and offPOWER ON/OFF LED - Indicates power on or offREMOVABLE COVER LENS - Covers th

7RS-232INTERFACEIRLRAUDIO OUTPUT12VDC 1.5AINOUTNEWMARKET, NH U.S.A.ST2 Smart Tuner LINKKEYPAD PORTSTUNER 1TUNER 2FM COAXLOOPANTENNAFM COAXLOOPANTENNAS

8TUNETUNEFAV 1SEEKST/ MONOLOC/ DXSEEKTUNETUNER 1 TUNER 24MEMBANK123567890PWRMEMTUNEAM/FMFAV 2OKPOWER - Puts the tuner in/out of standby modeTUNER CONT

9ST2 SETUP AND CONNECTIONSBASIC CONNECTIONSPowerTo power the tuner, connect the 12VDC externalpower supply by inserting the power supply jackinto the